SYSSIZE=0x8000
;
;	boot.s
;
; boot.s is loaded at 0x7c00 by the bios-startup routines, and moves itself
; out of the way to address 0x90000, and jumps there.
;
; It then loads the system at 0x10000, using BIOS interrupts. Thereafter
; it disables all interrupts, moves the system down to 0x0000, changes
; to protected mode, and calls the start of system. System then must
; RE-initialize the protected mode in it's own tables, and enable
; interrupts as needed.
;
; NOTE! currently system is at most 8*65536 bytes long. This should be no
; problem, even in the future. I want to keep it simple. This 512 kB
; kernel size should be enough - in fact more would mean we'd have to move
; not just these start-up routines, but also do something about the cache-
; memory (block IO devices). The area left over in the lower 640 kB is meant
; for these. No other memory is assumed to be "physical", ie all memory
; over 1Mb is demand-paging. All addresses under 1Mb are guaranteed to match
; their physical addresses.
;
; NOTE1 abouve is no longer valid in it's entirety. cache-memory is allocated
; above the 1Mb mark as well as below. Otherwise it is mainly correct.
;
; NOTE 2! The boot disk type must be set at compile-time, by setting
; the following equ. Having the boot-up procedure hunt for the right
; disk type is severe brain-damage.
; The loader has been made as simple as possible (had to, to get it
; in 512 bytes with the code to move to protected mode), and continuos
; read errors will result in a unbreakable loop. Reboot by hand. It
; loads pretty fast by getting whole sectors at a time whenever possible.

; 1.44Mb disks:
sectors = 18
; 1.2Mb disks:
; sectors = 15
; 720kB disks:
; sectors = 9

.globl begtext, begdata, begbss, endtext, enddata, endbss
.text
begtext:
.data
begdata:
.bss
begbss:
.text

BOOTSEG = 0x07c0
INITSEG = 0x9000
SYSSEG  = 0x1000			; system loaded at 0x10000 (65536).
ENDSEG	= SYSSEG + SYSSIZE

entry start
start:
	mov	ax,#BOOTSEG
	mov	ds,ax
	mov	ax,#INITSEG
	mov	es,ax
	mov	cx,#256
	sub	si,si
	sub	di,di
	rep
	movw
	jmpi	go,INITSEG
go:	mov	ax,cs
	mov	ds,ax
	mov	es,ax
	mov	ss,ax
	mov	sp,#0x400		; arbitrary value >>512

	mov	ah,#0x03	; read cursor pos
	xor	bh,bh
	int	0x10
	
	mov	cx,#24
	mov	bx,#0x0007	; page 0, attribute 7 (normal)
	mov	bp,#msg1
	mov	ax,#0x1301	; write string, move cursor
	int	0x10

; ok, we've written the message, now
; we want to load the system (at 0x10000)

	mov	ax,#SYSSEG
	mov	es,ax		; segment of 0x010000
	call	read_it
;	call	kill_motor

; if the read went well we get current cursor position ans save it for
; posterity.

	mov	ah,#0x03	; read cursor pos
	xor	bh,bh
	int	0x10		; save it in known place, con_init fetches
	mov	[510],dx	; it from 0x90510.
		
; now we want to move to protected mode ...

	cli			; no interrupts allowed !

; first we move the system to it's rightful place

	mov	ax,#0x0000
	cld			; 'direction'=0, movs moves forward
do_move:
	mov	es,ax		; destination segment
	add	ax,#0x1000
	cmp	ax,#0x9000
	jz	end_move
	mov	ds,ax		; source segment
	sub	di,di
	sub	si,si
	mov 	cx,#0x8000
	rep
	movsw
	j	do_move

; then we load the segment descriptors

end_move:

	mov	ax,cs		; right, forgot this at first. didn't work :-)
	mov	ds,ax
	lidt	idt_48		; load idt with 0,0
	lgdt	gdt_48		; load gdt with whatever appropriate

; that was painless, now we enable A20

;;; 	call	empty_8042
;;; 	mov	al,#0xD1		; command write
;;; 	out	#0x64,al
;;; 	call	empty_8042
;;; 	mov	al,#0xDF		; A20 on
;;; 	out	#0x60,al
;;; 	call	empty_8042

; well, that went ok, I hope. Now we have to reprogram the interrupts :-(
; we put them right after the intel-reserved hardware interrupts, at
; int 0x20-0x2F. There they won't mess up anything. Sadly IBM really
; messed this up with the original PC, and they haven't been able to
; rectify it afterwards. Thus the bios puts interrupts at 0x08-0x0f,
; which is used for the internal hardware interrupts as well. We just
; have to reprogram the 8259's, and it isn't fun.

	mov	al,#0x11		; initialization sequence
	out	#0x20,al		; send it to 8259A-1
	.word	0x00eb,0x00eb		; jmp $+2, jmp $+2
	out	#0xA0,al		; and to 8259A-2
	.word	0x00eb,0x00eb
	mov	al,#0x20		; start of hardware int's (0x20)
	out	#0x21,al
	.word	0x00eb,0x00eb
	mov	al,#0x28		; start of hardware int's 2 (0x28)
	out	#0xA1,al
	.word	0x00eb,0x00eb
	mov	al,#0x04		; 8259-1 is master
	out	#0x21,al
	.word	0x00eb,0x00eb
	mov	al,#0x02		; 8259-2 is slave
	out	#0xA1,al
	.word	0x00eb,0x00eb
	mov	al,#0x01		; 8086 mode for both
	out	#0x21,al
	.word	0x00eb,0x00eb
	out	#0xA1,al
	.word	0x00eb,0x00eb
	mov	al,#0xFF		; mask off all interrupts for now
	out	#0x21,al
	.word	0x00eb,0x00eb
	out	#0xA1,al

; well, that certainly wasn't fun :-(. Hopefully it works, and we don't
; need no steenking BIOS anyway (except for the initial loading :-).
; The BIOS-routine wants lots of unnecessary data, and it's less
; "interesting" anyway. This is how REAL programmers do it.
;
; Well, now's the time to actually move into protected mode. To make
; things as simple as possible, we do no register set-up or anything,
; we let the gnu-compiled 32-bit programs do that. We just jump to
; absolute address 0x00000, in 32-bit protected mode.

	mov	ax,#0x0001	; protected mode (PE) bit
;	lmsw	ax		; This is it!
	mov cr0, eax
	jmpi	0,8		; jmp offset 0 of segment 8 (cs)

; This routine checks that the keyboard command queue is empty
; No timeout is used - if this hangs there is something wrong with
; the machine, and we probably couldn't proceed anyway.
empty_8042:
	.word	0x00eb,0x00eb
	in	al,#0x64	; 8042 status port
	test	al,#2		; is input buffer full?
	jnz	empty_8042	; yes - loop
	ret

; This routine loads the system at address 0x10000, making sure
; no 64kB boundaries are crossed. We try to load it as fast as
; possible, loading whole tracks whenever we can.
;
; in:	es - starting address segment (normally 0x1000)
;
; This routine has to be recompiled to fit another drive type,
; just change the "sectors" variable at the start of the file
; (originally 18, for a 1.44Mb drive)
;
sread:	.word 1			; sectors read of current track
head:	.word 0			; current head
track:	.word 0			; current track
read_it:
	mov ax,es
	test ax,#0x0fff
die:	jne die			; es must be at 64kB boundary
	xor bx,bx		; bx is starting address within segment
rp_read:
	mov ax,es
	cmp ax,#ENDSEG		; have we loaded all yet?
	jb ok1_read
	ret
ok1_read:
	mov ax,#sectors
	sub ax,sread
	mov cx,ax
	shl cx,#9
	add cx,bx
	jnc ok2_read
	je ok2_read
	xor ax,ax
	sub ax,bx
	shr ax,#9
ok2_read:
	call read_track
	mov cx,ax
	add ax,sread
	cmp ax,#sectors
	jne ok3_read
	mov ax,#1
	sub ax,head
	jne ok4_read
	inc track
ok4_read:
	mov head,ax
	xor ax,ax
ok3_read:
	mov sread,ax
	shl cx,#9
	add bx,cx
	jnc rp_read
	mov ax,es
	add ax,#0x1000
	mov es,ax
	xor bx,bx
	jmp rp_read

read_track:
	push ax
	push bx
	push cx
	push dx
	mov dx,track
	mov cx,sread
	inc cx
	mov ch,dl
	mov dx,head
	mov dh,dl
	mov dl,#0
	and dx,#0x0100
	mov ah,#2
	int 0x13
	jc bad_rt
	pop dx
	pop cx
	pop bx
	pop ax
	ret
bad_rt:	mov ax,#0
	mov dx,#0
	int 0x13
	pop dx
	pop cx
	pop bx
	pop ax
	jmp read_track

/*
 * This procedure turns off the floppy drive motor, so
 * that we enter the kernel in a known state, and
 * don't have to worry about it later.
 */
kill_motor:
	push dx
	mov dx,#0x3f2
	mov al,#0
	outb
	pop dx
	ret

gdt:
	.word	0,0,0,0		; dummy

	.word	0x07FF		; 8Mb - limit=2047 (2048*4096=8Mb)
	.word	0x0000		; base address=0
	.word	0x9A00		; code read/exec
	.word	0x00C0		; granularity=4096, 386

	.word	0x07FF		; 8Mb - limit=2047 (2048*4096=8Mb)
	.word	0x0000		; base address=0
	.word	0x9200		; data read/write
	.word	0x00C0		; granularity=4096, 386

idt_48:
	.word	0			; idt limit=0
	.word	0,0			; idt base=0L

gdt_48:
	.word	0x800		; gdt limit=2048, 256 GDT entries
	.word	gdt,0x9		; gdt base = 0X9xxxx
	
msg1:
	.byte 13,10
	.ascii "Loading system ..."
	.byte 13,10,13,10

.text
endtext:
.data
enddata:
.bss
endbss: